What test modes does the MOB1 have?
There are three test modes on the MOB1; Functional, DSC and AIS/GPS.
The Functional test should be carried out once a month and will display the length of time the battery has been used for. It will also apply a load to the battery to test that the battery is not faulty or has been discharged. It carries out other functional tests on the electronic circuitry. It does not test the GPS or make test transmissions.
The DSC test should be carried out no more than two times a year. This test sends a single DSC transmission to the MMSI programmed into the MOB1, which will be displayed on the vessels DSC radio. It does not send a Distress or Distres Relay call and the call does not contain the position.
The AIS test should be carried out no more than three times a year. This test activates the GPS receiver and after the position is determined it makes an AIS transmission, which will display on a suitable AIS receiver or chartplotter. The received AIS message will show the position determined by the MOB1 GPS receiver. There is also a transmission of the AIS text message containing the words “MOB TEST”. Note that this test must be done with the MOB1 in full view of the sky. Without a valid position, the MOB1 will not transmit any AIS messages.
The limitation on the number of tests a year is to ensure that the battery will still have its full operational life at the expiry date of the battery.
Why does my MOB1 show red flashes if I try to programme the MMSI number?
If the unit fails to programme, showing the flashing red LED on completion, please try again. Turn the MOB1 on in programming mode again and retry. There is no need to exit the programming screen on the programme. If the programming page is showing, simply press F10 again to commence the programming sequence again. Note that the red flashing may tecke several seconds to start after the on screen sequence has finished.
If you are having problems programming your MOB1, please check the following guidance.
1) Make sure that your screen brightness is set to maximum, using the controls on the monitor or device.
2) Ensure that you have commenced programming within 50 seconds of putting the MOB1 into programming mode. Failure to do this will cause the MOB1 to have turned off before communication starts. Note that once programming has commenced (The white box is flashing) the MOB1 should stay on until the programming sequence is completed. Ideally the MOB1 should be put into programming mode just before placing the MOB1 in front of the white square.
3) Ensure that the MOB1 is placed over the white square with the rubber programming adaptor firmly touching the screen and with the aperture in the rubber close to the centre of the white box.
4) Avoid programming the MOB1 in bright ambient light conditions. If necessary point the screen away from direct or bright sources of light such as sun through a window. (In extreme circumstances, especially with older screens that have lost their brightness, place a thick cloth over the screen and MOB1 to block out the ambient light.)
5) The MOB1 configuration software requires precise timing, which may be disrupted by other applications running at the same time, especially on slower computers. If you still encounter problems, try shutting down all un-necessary applications, including anti-virus software.
6) On laptops, the F10 key will require using in conjunction with the Function (labelled Func or Fn) to start the white box flashing black and white to send the data to the MOB1. Most keyboards will colour the F keys in the same colour as the Function key to identify this.
7) The MOB1 MMSI programming software is only available for Windows PCs. For users of other operating systems and smart phones and tablets there is an online application available. This can be accessed using the
button on the installers web page. Note that it can only be used online.
Which DSC radios are compatible with the MOB1?
Ocean Signal recommends using one of the radios from the list below with the rescueME MOB1. The following class D DSC radios have been tested in cooperation with the manufacturer and confirmed to receive the Individual Distress Relay call.
ICOM:
Current models; M91, M323, M423, M506
Older models; M411, M421, M505, M603
Simrad: RS90
Standard Horizon: The factory has confirmed the following models are compatible:
GX5500S
V4.xx (GX5500S only),
<GX2200/GX2150/GX2000>
V5.xx (ALL)
V4.xx (GX2150/GX2000 only)
V1.xx (GX2200 only)
<GX1700/GX1600>
V4.xx (ALL)
V2.xx (ALL)
<GX1300>
V2.xx (ALL)
V1.xx (ALL)
<GX1200>
V1.xx (ALL)
Class A DSC radios have always been able to receive this call and all models are believed to be compatible.
This list is not exhaustive and will be added to as more compatible models are confirmed.
Ocean Signal welcomes enquiries from other manufacturers wishing to have their radios listed here.
What DSC functions are allowed in my country?
The DSC functionality of the MOB1 is limited by regulations in each country. The list below indicates which functions you may expect.
AIS only: Canada, Denmark, Latvia
AIS + DSC Individual Distress Relay call plus group call sent after 30minutes: USA
AIS + DSC Individual Distress Relay call only: France, Germany, Netherlands, Spain, United Kingdom
AIS + DSC Individual Distress Relay, All Ships Distress Alert (manual initiation only): All other European countries
AIS + DSC Individual Distress Relay, All Ships Distress Alert, sent once on MOB1 activation and on manual initiation: Rest of the World.
How to programme DSC MMSI number into the MOB1
A video showing the programming sequence for the MOB1 can be found at this link.. Remember to set the display brightness to full before starting the sequence.
Note that the test key is being pressed directly and then the rubber adaptor fitted when the MOB is ready to programme.
Can I cange the DSC MMSI number is I move to a different vessel?
Yes, it is possible to reprogram the MMSI number used to call your DSC radio as many times as you like using the normal applications. There is no need to delete the old number first. The new number will simply overwrite the old MMSI number.
Each time you programme the MOB1 it will use a small amount of the battery capacity and reduce the operating lifetime by a few minutes each time.
Why does the displayed MMSI not change when I enter my DSC MMSI number?
All AIS and DSC MOBs are pre programmed at the time of manufacture with the self identification MMSI number. In the case of the rescueME MOB1, or the M100, this number will always start 97260—-. The 972 identities the device as an MOB device and the 60 identifies the device as manufactured by Ocean Signal.
It is not possible for the user to change this number, which is a requirement of the relevant approval standards.
The DSC MMSI number programmed in by the user is the number the MOB1 will send the distress calls to. Compatible radios will still show the ‘from’ MMSI number as the 972 number printed on the rear of the MOB1. Likewise the target displayed on an AIS plotter will also show with the target address as the 972 number.
What is the black cord supplied for?
The provided length of cord is supplied as a safeguard against accidental loss. The cord (lanyard) should be used to tether the MOB1 to a fixed point on the lifejacket that will not inhibit inflation or detach/untie if the MOB1 is accidentally removed from its bracket. The MOB1 fixing point for the cord is located on the top of the unit.